Contents
How do you fix an open sketch in SolidWorks?
To open the Repair Sketch tool: Click Tools > Sketch Tools > Repair Sketch. Repair Sketch deletes these from the sketch.
What is an open sketch in SolidWorks?
Unless you’re creating a Thin Feature Revolve then SolidWorks can only Revolve a closed profile. This means that you need to have no gaps or breaks around the outside of your profile.
How do you close open contours in SolidWorks?
Click Tools > Sketch Tools > Close Sketch to Model. An arrow points in the direction in which the sketch will close. (The extruded boss will either be within the sketch lines or outside of the sketch lines.) In the dialog box, select Reverse direction to close the sketch, if necessary.
Can you extrude open sketch in SolidWorks?
You can extrude base features and other features using Extrude (2D to 3D toolbar) with partial sketches. Click Extrude (2D to 3D toolbar), or click Tools > Sketch Tools > 2D to 3D > Extrude, and click in the graphics area to establish the direction of the extrusion. …
Can you extrude an open contour?
For example, an Extrude with an open contour will appear as “Extrude-Thin1” in the feature tree as seen in the above image. The above image depicts the comparison between a regular Boss Extrude, Cut Extrude and Revolve with their respective thin feature counterparts.
How do I make a closed sketch in Solidworks?
Click Tools > Sketch Tools > Close Sketch to Model . An arrow points in the direction in which the sketch will close. (The extruded boss will either be within the sketch lines or outside of the sketch lines.) In the dialog box, select Reverse direction to close the sketch, if necessary.
How do you add a derived sketch in Solidworks?
Select the sketch from which you want to derive a new sketch. Hold the Ctrl key and click the face on which you want to place the new sketch. Click Insert > Derived Sketch. The sketch appears on the plane of the selected face, and the status line indicates that you are editing the sketch.
What is a self intersecting contour?
“Self Intersecting contour” means a closed-loop polygon of the same the beginning and the end position and intersected with self-line in between. If there is such a polygon, the entire area might not be able to be filled well when the gerber output.
How should the warning shown here be repaired?
How should the warning shown here be repaired? Select a new face or plane to replace the missing one.
When creating sketches small boxes show up next to the sketch lines What are these boxes called?
This small box called PARAMETRIC indicator, you can get him away by delete all constrains .
Can we extrude the sketch in both direction yes or no?
To extrude in both directions from the sketch plane in the PropertyManager, under Direction 1, select Through All – Both Directions. To extrude as a thin feature, set the PropertyManager options in Thin Feature.
How do you extrude a 2D sketch in Solidworks?
Click Convert to Extrusion (2D to 3D toolbar), or click Tools > Sketch Tools > 2D to 3D > Extrude, and click in the graphics area to establish the direction of the extrusion. The Base-Extrude PropertyManager appears.
What are open contours?
Contours can be either open or closed. A contour must be closed to obtain measurements of the area within the contour. An open contour can be used to measure the length of a curved line.
What is extruded cut solidworks?
Extruded cut feature removes material from the part. The End Condition, Draft, and Thin Feature options are same as described in Extruded Boss/Base. To create an extruded cut: 1) Sketch the profile for cut. 2) Click Extruded Cut on the Features toolbar or select Insert, Cut, Extrude on the menu bar.
What is a thin feature solidworks?
The Thin Feature tool takes the sketched profile and creates a constant thickness in the sketch plane. One good example of this is a hollow tube. Instead of creating two circles in the sketch, you can just sketch one and then specify the thickness within the Extrude.
