Contents
Can you merge parts in Solidworks?
You cannot combine two separate parts. However, you can create a multibody part by using Insert Part to place one part into the other part file. Then you can use Combine on the multibody part. (Features toolbar) or Insert > Features > Combine.
How do you extrude in Solidworks?
Click Convert to Extrusion (2D to 3D toolbar), or click Tools > Sketch Tools > 2D to 3D > Extrude, and click in the graphics area to establish the direction of the extrusion. The Base-Extrude PropertyManager appears. Edit the properties in the Base Extrude PropertyManager.
How do you close open contours in Solidworks?
Click Tools > Sketch Tools > Close Sketch to Model. An arrow points in the direction in which the sketch will close. (The extruded boss will either be within the sketch lines or outside of the sketch lines.) In the dialog box, select Reverse direction to close the sketch, if necessary.
What is merge result in Solidworks?
Merge Results In simplest terms, a multibody solid is a single part file with two or more bodies that are not merged together. … In advanced part design, there are occasions when an extrusion that would normally be merged to the existing solid might function better if the extrusion was not merged.
What does Defeature do in Solidworks?
You can use the Defeature tool to remove details from assemblies, multibody parts, and single-body parts. Save the details to a new file where the details are replaced by dumb solids. Dumb solids are solids without feature definition or history.
How do I simplify a Solidworks model?
Click Simplify (Tools toolbar) or Tools > Find/Modify > Simplify. On the Simplify Task Pane: Select items in Features to specify the types of features to search for. Set the Simplification factor to increase or decrease the insignificant volume factor.
What is convert entities for?
The Convert Entities tool allows users to make a copied projection of a given sketch, face, or set of edges onto the active sketch plane. These sketch entities will update their size and/or positioning if either of these characteristics changes in the source sketch.
What is convert entities & where is used?
Convert Entities and Offset Entities are two powerful tools you can use when editing a sketch in SOLIDWORKS. Let’s begin with the Convert Entities tool. Whenever we need to make a sketch entity that matches other geometry of our model we can use the Convert Entities tool.
Why we use convert entities in Solidworks?
You can create one or more curves in a sketch by projecting an edge, loop, face, curve, or external sketch contour, set of edges, or set of sketch curves onto the sketch plane. Search ‘Convert Entities’ in the SOLIDWORKS Knowledge Base.
What type of geometry can be used to create lofts?
Answer: Lofts can use 3D sketch curves to define profiles as well as guide curves. You can even create a Loft from one single 3D sketch containing all of the geometry needed to define profiles and guide curves. But each profile must be made up of geometry that is planar to each other.
Can a open sketch be extruded in Solidworks?
Set the PropertyManager options. To extrude in both directions from the sketch plane in the PropertyManager, under Direction 1, select Through All – Both Directions. To extrude as a thin feature, set the PropertyManager options in Thin Feature.
Click Extrude (2D to 3D toolbar), or click Tools > Sketch Tools > 2D to 3D > Extrude, and click in the graphics area to establish the direction of the extrusion.
How should the warning shown here be repaired?
How should the warning shown here be repaired? Select a new face or plane to replace the missing one.
What is a closed sketch in Solidworks?
Closes a sketch with an open profile, using existing model edges. To use an open profile sketch to extrude using existing model edges: Open a sketch on a model face. Sketch an open profile with endpoints that are coincident with model edges on the same face boundary.
How do you save a Solidworks assembly as a shell?
To save an assembly as a part, we use the File > Save As command. After . sldprt file type is selected, three options appear in the Save As dialog: Exterior faces – saved part includes external faces only, all bodies being surfaces.
