Contents
What is a counterbored hole?
A counterbore (symbol: ⌴) is a cylindrical flat-bottomed hole that enlarges another coaxial hole, or the tool used to create that feature. A counterbore hole is typically used when a fastener, such as a socket head cap screw, is required to sit flush with or below the level of a workpiece’s surface.
What is hole Wizard in Solidworks?
Hole Wizard is a tool inside SOLIDWORKS that allows you to quickly create holes within a part or assembly without the need of drawing or using multiple features. The Hole Wizard is made up of two tabs, the first: Type, covers the creation of the hole.
What is exploded view in Solidworks?
When you explode multiple components in one step, you can space them equally along an axis. You can edit an explode step to add, delete, or reposition components. You can edit an explode step while you create the exploded view or after you save the view. You can delete an explode step from an exploded view.
How do you properly drill a hole in metal?
Use a heavier, sharp punch to re-punch the smaller mark and make a dimple. Be careful here because sometimes a punch mark will work harden the metal and will actually be harder to drill than it should be. Use a small bit to drill a pilot hole.
How do you show counterbore hole in drawing?
Dimensioning Counterbore Hole Select Dimension Tool in the Annotate Tab > Double Click on the outer circle o the counterbore (NOTE Leader Arrows should always point to the larger hole) This will place the diameter of the large hole Page 9 4.
How do you make a counterbore hole?
To counterbore a hole, it’s easiest to drill the larger-diameter hole first, then drill the deeper hole for the fastener’s shaft. You should use a spade bit-or, better-a Forstner bit, which will create a flat-bottomed hole. It’s hard to say where the term counterbore came from.
What is the difference between tapped hole and bottoming tapped hole?
the only difference what i could find is that the drill depth. Tapped hole have aproximately 2mm more drill depth when compared with bottoming tapped holes.
How do you use hole Wizard?
You can use the Hole Wizard to create customized holes of various types. To create hole wizard holes, create a part and select a surface, click Hole Wizard (Features toolbar) or Insert > Features > Hole > Wizard, set the PropertyManager options, and click .
How do you remove exploded view in Solidworks?
Right-click ExplView and click Edit Feature. Under Explode Steps, right-click an explode step and select Delete. Expand the exploded view, ExplView , and right-click an explode step . Select Delete.
Can you drill through a live bullet?
It is extremely unsafe to drill into a live primer.
What is a drill block used for?
The Milescraft drill block allows you to drill straight holes all of the time, on many different drilling surfaces. On the bushing block, there are 6 holes for common drill bits sizes.
Can I use wd40 for drilling metal?
WD-40 will work just fine as a cutting oil. … For drilling holes in steel that’s 1/8 in. or thicker, use cutting fluid or a multipurpose oil like 3-IN-ONE. Lubricating the bit reduces friction and heat buildup, which makes drilling easier and your bits last longer.
How can you make a hole in metal bigger without a drill?
To make a hole bigger without a drill, you need to get either sandpaper and a dowel, a hand file, or a jab saw. It’s helpful to draw the size of the circle needed first, then manually file the excess wood until the hole is the right size. Wipe away the dust and your project is ready to continue.
What drill bit is best for steel?
DRILL BIT MATERIALS Cobalt (HSCO) is considered an upgrade from HSS because it includes 5-8% Cobalt blended into the base material. This is a great option for drilling into harder steel as well as stainless steel grades. Carbide (Carb) is the hardest and most brittle of the drill bit materials.
What is the best angle to make a hole using a power drill?
Up to 45 degrees, you can easily drill an angled hole. Between 45 degrees and 15 degrees, the process becomes more difficult but not impossible. Lower than 15 degrees, the drill will move around too much.
